Billion 5102G Manual de instrucciones

Telkom ADSL 5102G Instruction Manual

2.4 The Rear Ports Telkom 5102G 23 451 Port Meaning 1 Power Switch Power ON/OFF switch 2 PWR Connect the supplied power adapter to this soc

the LAN Link and ADSL line LEDs are lit. If they are not, verify that you are using the proper cables. Ensure that all other devices connected to the

Chapter 3 Basic Installation The router can be configured with your web browser. A web browser is included as a standard application in the follo

Configuring PC in Windows XP 1. Go to Start / Control Panel (in Classic View). In the Control Panel, double-click on Network Connections 2. Doubl

Configuring PC in Windows 2000 1. Go to Start / Settings / Control Panel. In the Control Panel, double-click on Network and Dial-up Connections. 2. D

Configuring PC in Windows 98/Me 1. Go to Start / Settings / Control Panel. In the Control Panel, double-click on Network and choose the Configuration

Configuring PC in Windows NT4.0 1. Go to Start / Settings / Control Panel. In the Control Panel, double-click on Network and choose the Protocols tab

3.2 Factory Default Settings Before configuring your router, you need to know the following default settings. Web Interface: Username: admin Pas

3.3 LAN and WAN Port Addresses The parameters of LAN and WAN ports are pre-set in the factory. The default values are shown below. LAN Port WAN Port

3.5 Configuring with your Web Browser Open your web browser, enter the IP address of your router, which by default is 10.0.0.2, and click “Go”, a user

Chapter 1 ...1 1.1 Intr

Chapter 4 Configuration At the configuration homepage, the horizontal navigation pane where bookmarks are provided links you directly to the desi

For detailed instructions on configuring WAN settings, see the WAN section of this manual. The information you need for the Quick Start wizard to get

Step 1: Set your new password. 20

Step 2: Time Zone selection which is already selected for South Africa by default. Step 3: Select your connection type 21

Step 4: Enter your ISP information Step 5: Complete Wizard 22

Step 6: Save changes Step 7: Restart your ADSL Router 23

4.2 Interface Setup Click this item to access the following sub-items that configure the ADSL router: Internet, LAN, and Wireless These functions are

ATM VC Virtual Circuit: VPI (Virtual Path Identifier) and VCI (Virtual Channel Identifier) define a virtual circuit. VPI: The valid range for the V

mask assigned to you by your ISP (if given). Gateway: You must specify a gateway IP address (supplied by your ISP) when you use 1483 Bridged IP in th

Router Local IP IP Address: Enter the IP address of ADSL Router in dotted decimal notation, for example, 10.0.0.2 (factory default). IP Subnet Mask

Chapter 1 Introduction to the Telkom ADSL 5102G 1.1 Introducing the Telkom ADSL 5102G Welcome to the Telkom ADSL 5102G ADSL2+ Router. Your Telkom rout

This section introduces the wireless LAN and some basic configurations. Wireless LANs can be as simple as two computers with wireless LAN cards commu

Setting your wireless client connections to the Telkom 5102G Step 1: Click on Start/Control Panel/Network Connections/Wireless Networks Tab Step 2.

Step 3: Input the details of your Telkom 5102G router. Default: SSID: wlan-ap Network Authentication: WPA-PSK Date encryption: TKIP Network

Broadcast SSID: Select Yes to hide the SSID in so a station cannot obtain the SSID through passive scanning. Select No to make the SSID visible so a

devices to configure this screen. To change your router’s MAC filter settings, click Wireless LAN, MAC Filter to open the MAC Filter screen. The scree

Encryption: TKIP (Temporal Key Integrity Protocol) utilizes a stronger encryption method and incorporates Message Integrity Code (MIC) to provide pr

#: Item number Dest IP: IP address of the destination network Mask: The destination mask address. Gateway IP: IP address of the gateway or existi

forwarded. Metric：It represents the cost of transmission for routing purposes. The number need not be precise, but it must be between 1 and 15. Anno

The DMZ Host is a local computer exposed to the Internet. When setting a particular internal IP address as the DMZ Host, all incoming packets will be

The reason for this is that when using NAT, your publicly accessible IP address will be used by and point to your router, which then needs to deliver

to target a machine on your network. Secondly, it can block and redirect certain ports to limit the services that outside users can access. For exam

Rule Index: Choose the rule number. Rule Type: One-to-one: This is the mode maps one local IP address to one global IP address. Note that port numb

Public Start IP: This is the starting Inside Public IP Address. Enter 0.0.0.0 here if you have a dynamic IP address from your ISP. Public End IP: Th

4.3.3 ADSL ADSL Mode: The default setting is Auto Sync-UP. This mode will automatically detect your ADSL, ADSL2+, ADSL2, G.dmt, G.lite, and T1.413.

ACL Rule Index: This is item number Secure IP Address: The default 0.0.0.0 allows any client to use this service to remotely manage the Telkom ADSL

IP Filter Set Editing IP filter Set Index: This is item number Interface: Select which channel (PVC) to configure. Direction: Select the access

Subnet Mask: It is the destination IP addresses based on above destination subnet IP Source Port Number: This Port or Port Ranges defines the port a

Get Community: Type the Get Community, which is the password for the incoming Get-and GetNext requests from the management station. Set Community:

application to open the web configuration’s login screen without entering the Telkom ADSL 5102G’s IP address Auto-configured: Select this check box t

E-mail Address: Type your e-mail address. Username: Type your user name. Password: Type the password assigned to you. Wildcard support: Select thi

Synchronize time with: Select the time service protocol that your time server sends when you turn on the Router. Time Zone: Choose the time zone of

while providing the WEP and WPA for securing your wireless networks. Fast Ethernet Switch A 10/100Mbps fast Ethernet switch is built in with auto

New Firmware Location: Type in the location of the file you want to upload in this field or click Browse to find it. Browse: Click Browse... to fin

DO NOT power down the router or interrupt the firmware upgrading while it is still in process. Improper operation could damage the router. Warni

4.6 Status 4.6.1 Device Info 50

Device Information Firmware version: This is the Firmware version MAC Address: This is the MAC Address LAN IP Address: LAN port IP address. Sub

4.6.3 Statistics Read-only information here includes port status and packet specific statistics. Also provided are "Transmit Statistics" a

Transmit Frames: This field displays the number of frames transmitted in the last second. Transmit Multicast Frames: This field displays the number

Chapter 5 Troubleshooting If the Telkom ADSL2+ Router is not functioning properly, you can refer first to this chapter for simple troubleshooting

Problems with the WAN Interface Problem Corrective Action Initialization of the PVC connection (“linesync”) failed. Ensure that the telephone cable i

APPENDIX Product Support and Contact Information Most problems can be solved by referring to the Troubleshooting section in the User’s Manual or Qu

service, you must first apply for an account from a DDNS service like http://www.dyndns.org/. PPP over Ethernet (PPPoE): Provides embedded PPPoE

Rich management interfaces Supports flexible management interfaces with local LAN port and WAN port. Users can use Telnet, WEB GUI, and SNMP thr

Chapter 2 Installing the Telkom ADSL 5102G 2.1 Important note for using the Telkom ADSL 5102G Router 9 Do not use the Telkom ADSL 5102G in high hu

2.3 The Front LEDs Telkom 5102G LED Meaning 1 PWR: Lit when power is ON. 2 SYS: Lit when the system is ready. 3 WLAN： Lit green